null

Free Ground Shipping for PowerKnobs and PowerWheels

phone: (508) 995-9711

Service Parts

Here you will find Edson sailboat steering hardware, which includes chain & kire kits, pull-pull conduit steering, chain sprockets and much more. For more information about which products are right for your application, please see our support section for boat-specific data sheets, how-to videos and other helpful resources. Our blog section contains many helpful articles, including an in-depth discussion of achieving correct steering cable tension.

72 of 172 Items
  • Vision II Pedestal Rebuild Kit (314-476)

    Vision II Pedestal Rebuild Kit (314-476)

    Bring new life to your Edson Vision II Pedestal (#476) with this complete Rebuild Kit. Edson's #476 Pedestal Rebuild Kit replaces all of the important moving parts that will make your Pedestal run smoothly again.   #476 Pedestal Maintenance Kit...

    $151.00
    Add to Cart
  • Pedestal Rebuild Kit (314-335)

    Pedestal Rebuild Kit (314-335)

    Bring new life to an older but still good Edson #335 & #336 Pedestal with this complete Rebuild Kit. Edson's #314-335 Pedestal Rebuild Kit replaces all of the important moving parts that will make your pedestal run smoothly again.  The...

    $127.00
    Add to Cart
  • 6" Aluminum Hex Head Pedestal Bolt (646-6HEX)

    6" Aluminum Hex Head Pedestal Bolt (646-6HEX)

    Since 1987, all Edson Pedestals use the exclusive Edson Hex Head Aluminum Bolts. With this improvement they lock in place and require only one person to tighten them. They fit flush with the base and the aluminum alloy is the same as the base thus...

    $13.00
    Add to Cart
  • 6” Aluminum Sheave (ONLY)

    6” Aluminum Sheave (ONLY)

    Edson’s Sheaves may be the answer in many areas of custom boat building, not only for steering but also for centerboards, custom deck hardware, or remote actuators, such as emergency shut off valves and CO2 systems. Great care should be...

    $120.00
    Add to Cart
  • Flat Conduit Idler with Needle Bearings - 6" Sheave Flat Conduit Idler with Needle Bearings - 6" Sheave

    Flat Conduit Idler with Needle Bearings - 6" Sheave

    Edson’s Flat Conduit Idler allow you to turn steering cable around a sheave rather than through the conduit, reducing wear and friction. Constructed of anodized Aluminum sheaves and a Brass housing, it is designed to be mounted to a...

    $322.00
    Add to Cart
  • Single Upright Aluminum Sheave Assembly - 8" Sheave

    Single Upright Aluminum Sheave Assembly - 8" Sheave

    Edson’s Single Upright Aluminum Sheave Assembly with a 8" Sheave are specially designed for use in wire rope steering systems for sailboats. The Aluminum Sheaves are ideal for the performance boat that requires sensitive, lightweight steering...

    $558.00
    Add to Cart
  • Bronze Rudder Post Stuffing Box - 1.125" ID Bronze Rudder Post Stuffing Box - 1.125" ID Bronze Rudder Post Stuffing Box - 1.125" ID

    Bronze Rudder Post Stuffing Box - 1.125" ID

    Edson's Rudder Post Stuffing Box combines a rudder post bearing with an above-the-waterline stuffing box for. We recommend fiberglassing the stuffing box/bearing to the top of the tubing when the rudder post is in place. This can be done easily using...

    $244.00
    Add to Cart
  • In-Line Conduit Greaser for 853-250 Conduit In-Line Conduit Greaser for 853-250 Conduit In-Line Conduit Greaser for 853-250 Conduit

    In-Line Conduit Greaser for 853-250 Conduit

    Edson’s In-Line Conduit Greasers are a simple, efficient way to lubricate your conduit. One should be installed in an accessible area of straight conduit as close to the middle of each run as possible - preferably every 3’-5’ where...

    $81.00
    Add to Cart
  • 17" Conduit Bracket with Rudder Stop 17" Conduit Bracket with Rudder Stop

    17" Conduit Bracket with Rudder Stop

    Pull-Pull Conduit Bracket with Rudderstop is ideal for terminating the conduits at the quadrant when there are no bulkheads to utilize. It is easily bolted through the cockpit sole and comes with its own rudderstop post.  Edson’s #824-17...

    $264.00
    Add to Cart
  • In-Out Conduit Idler - 6" Sheave In-Out Conduit Idler - 6" Sheave In-Out Conduit Idler - 6" Sheave

    In-Out Conduit Idler - 6" Sheave

    In-Out Conduit Idler is designed to increase the efficiency and sensitivity of a Pull-Pull Conduit System. Engineered with 6” sheaves and three holes to accept Edson’s Conduit End Fittings, the idler makes wire alignment with the sheave...

    $416.00
    Add to Cart
  • Chain & Wire Kit - 2S15B13 (77105) Chain & Wire Kit - 2S15B13 (77105) Chain & Wire Kit - 2S15B13 (77105) Chain & Wire Kit - 2S15B13 (77105) Chain & Wire Kit - 2S15B13 (77105)

    Chain & Wire Kit - 2S15B13 (77105)

    Edson's Chain & Wire Kits are constructed of the highest quality marine-grade, non-magnetic materials! One length of roller chain and two lengths of wire are assembled with the connections between wire and chain covered in clear shrink...

    $354.00
    Add to Cart
  • O-Ring (960-A-1933)

    O-Ring (960-A-1933)

    Edson's O-Ring (960-A-1933) is designed for Edson's 335 Pedestals (Side Brake Model) & Edson's 336 Pedestal (Through Shaft Brake Model). Dimensions: ID: 1" OD: 1.25"

    $4.00
    Add to Cart
  • 6” Aluminum Sheave with Needle Bearings (ONLY)

    6” Aluminum Sheave with Needle Bearings (ONLY)

    Edson’s Sheaves may be the answer in many areas of custom boat building, not only for steering but also for centerboards, custom deck hardware, or remote actuators, such as emergency shut off valves and CO2 systems. Great care should be...

    $164.00
    Add to Cart
  • Flat Bronze Sheave Assembly - 4" Aluminum Sheave

    Flat Bronze Sheave Assembly - 4" Aluminum Sheave

    Edson’s Flat Sheave Assembly will allow you to turn steering cable around a sheave in tight areas where vertical assemblies normally wouldn't fit. Constructed of anodized Aluminum sheaves and a Bronze housing, it is designed to be...

    $230.00
    Add to Cart
  • Single Upright Aluminum Sheave Assembly - 10" Sheave

    Single Upright Aluminum Sheave Assembly - 10" Sheave

    Edson’s Single Upright Aluminum Sheave Assembly with a 10" Sheave are specially designed for use in wire rope steering systems for sailboats. The Aluminum Sheaves are ideal for the performance boat that requires sensitive, lightweight steering...

    $809.00
    Add to Cart
72 of 172 Items
!

© 2024 Edson Marine All rights reserved. | Sitemap