Service Kits and Parts

Flanged Bushing (Diamond Series Wheels Only)

Used on Diamond Series wheel where for the bolts that mount the wheel onto the flange. 

Superlube 1/2oz Tube

CDi Side Brake Collar - Bronze

CDi Brake Collar - Bronze. For CDi's with side brakes ONLY. A replacement for worn out brake collars found on CDi pedestals.  Machined to fit the downtube for even clamping force around it.  This is NOT compatible for CDi pedestals that use a...

Pedestal Bolts - Flats Kit

4 SS bolts - 1/2-13 x 4" flat head with nuts and Tefgel. Only for Classic Edson pedestals made prior to 1987. 1987 and after uses a hex head aluminum bolt. 

Sheave Pins for 4" Sheaves - Stainless Steel (960-A-1315)

In the early 1990s Edson upgraded the materials of sheave pins from brass to stainless steel. Brass pins were known to wear down over time creating complications in steering systems. For any boats made prior to that time period, please check your sheaves...

Sheave Pins for 6" Sheaves - Stainless Steel (960-A-1301)

In the early 1990s Edson upgraded the materials of sheave pins from brass to stainless steel. Brass pins were known to wear down over time creating complications in steering systems. For any boats made prior to that time period, please check your sheaves...

Brake Sleeve, Throttle/Engine Controls Sleeve (960-A-125)

This Delrin bushing is a replacement for worn or broken bushings on your 335 Edson pedestal with side brake, and on Edson engine controls. Used on the throttle and clutch lever n the 870ST-45 and 870ST-6. Used only on the throttle lever on the...

420 Bulkhead Steerer Rebuild Kit (314-420)

Bring new parts to your steering system with the Steerer Rebuild Kit. Edson's #314-420 Steerer Rebuild Kit replaces all of the important component parts that make up 420 Bulkhead Steerers.   #314-420 Pedestal Maintenance Kit includes: (2)...

Tef45 - 2 Gram Capsule (960-A-1466-2G)

THE ULTIMATE IN CORROSION PROTECTION. Protects, Lubricates, stops corrosion, prevents seizing and galling.  Won’t wash away in fresh or salt water or detergents.  MareLube™ TEF45™ is designed specifically for high...

Brake Maintenance Kit 316-689)

Just like your car, your boat’s wheel brake needs periodic relining. This kit includes all you need to make your brake work like new again. Compatible with 335, 400, and 410 pedestals with a side mount brake.    Click Here to see the How...

3/16" Woodruff Key - Tapered Shafts (684-187W)

Edson's 3/16" Woodruff Key is designed for Edson's Tapered Shafts or specifically for Edson's 336 Pedestal Through Shaft Brake Model.

Transom Boot (960-B-446)

Edson's 960-B-446 Transom Boot is apart of Edson's Transom Hung Rudder Steering System.  Ideal for boats with Transom Hung Rudders up to 27' (8.5m).

2" Vertical Rudder Stop (862-2)

Edson's 2" Vertical Rudder Stops are designed to limit the swing of the rudder.  Attached directly to an Edson Radial Drive Wheel or Edson's Pull-Pull Conduit Bracket to limit the swing of the Quadrant.   Bolts used are 3/8-16 x 1" long to...

3" Aluminum Hex Head Pedestal Bolt (646-3HEX)

Since 1987, all Edson Pedestals use the exclusive Edson Hex Head Aluminum Bolts. With this improvement they lock in place and require only one person to tighten them. They fit flush with the base and the aluminum alloy is the same as the base thus...

1/4" Square Wheel Key - Straight Shafts (684-250W)

Edson's 1/4" Square Wheel Key is designed for Edson's Straight Shafts for 335 Pedestals (Side Brake Model) & Edson's 336 Pedestal (Through Shaft Brake Model).

Stainless Sprocket - 11 Tooth for 5/8in #50 Chain (Thru Shaft Brake) (855-2-11-TSB)

Use Edson's double hub sprockets when space will allow; their extra length will spread the load. They are the same as the single hub sprockets but have a hub on both sides of the sprocket teeth with one side knurled for a brake. The Double Hub Sprocket...

Stainless Single Hub Sprocket - 11 Tooth for 5/8in #50 Chain (636-2-11-SS)

When space is limited, use Edson's non-magneticSingle Hub Sprockets. With the hub on one side, the sprocket takes up less space within the pedestal head.  These sprockets accept American Standard Roller Chains.   Part Number Material Hub...

Flax Packing for Stuffing Boxes

Waxed Flax packing for re-lining your stuffing box.  3/8” square x 16.5” long for rudderposts up to 4.5" diameter. Easily cut to fit for smaller rudderposts.

Conduit & Bearing Lubricant - 3oz tube of Teflon Grease

Edson’s Conduit Lubricant is a Teflon grease for use in all Edson Systems.  Ideal for both conduit and needle bearing use.   827-3 Conduit Lubricant - 3oz tube of Teflon Grease   !WARNING! DO NOT USE PETROLEUM BASED GREASE...

Tether-Style Rudder Stop (862-WIRE)

Edson's Tether-Style Rudder Stop is designed to limit the swing of your rudder, preventing costly damage from the rudder shock loading the steering system. Includes 6' of 2.5mm Dyneema rope to be spliced or tied to the radial and a...

4" Aluminum Hex Head Pedestal Bolt (646-4HEX)

Since 1987, all Edson Pedestals use the exclusive Edson Hex Head Aluminum Bolts. With this improvement they lock in place and require only one person to tighten them. They fit flush with the base and the aluminum alloy is the same as the base thus...

Drive Pin (pkg of 2) (960-A-95A)

Edson's Drive Pin (960-A-95A) is designed for Edson's 335 Pedestals (Edson's Side Brake Model). Includes 2 drive pins.

Stainless Steel Double Hub Sprocket - 11 Tooth for 5/8in #50 Chain (Side Mount Brake) (855-2-11SB)

Use Edson's double hub sprockets when space will allow; their extra length will spread the load. They are the same as the single hub sprockets but have a hub on both sides of the sprocket teeth with one side knurled for a brake. The Double Hub Sprocket...

Bronze Rudder Post Stuffing Box - 1" ID

Edson's Rudder Post Stuffing Box combines a rudder post bearing with an above-the-waterline stuffing box for. We recommend fiberglassing the stuffing box/bearing to the top of the tubing when the rudder post is in place. This can be done easily using...