null

Our office will be closed Thursday, 11/28 and Friday, 11/29 for Thanksgiving

Shop

Steering hardware, wheels, accessories, electronic mounts, and pumps highlight what Edson has to offer in this complete catalog of products.


  • Engine Control – Side Shift

    Engine Control – Side Shift

    Edson Clutch and Throttle Control is designed for transmissions that go into reverse when the cable is extended at the pedestal end. Also for harder to shift transmissions. Only for transmissions that specify 33 Series (Edson #734) Control...

    $562.00
  • Storage Rail Mount – Tapered Hub (Device Only)

    Storage Rail Mount – Tapered Hub (Device Only)

    Make more room in your cockpit when you’re not sailing! Enjoy a large wheel when sailing but it takes up too much room in the cockpit when you are at anchor or at the dock? Take your wheel off and store it out of the way with Edson’s Wheel...

    $169.00
  • Pedestal Rebuild Kit (314-335)

    Pedestal Rebuild Kit (314-335)

    Bring new life to an older but still good Edson #335 & #336 Pedestal with this complete Rebuild Kit. Edson's #314-335 Pedestal Rebuild Kit replaces all of the important moving parts that will make your pedestal run smoothly again.  The...

    $127.00
  • 6" Aluminum Hex Head Pedestal Bolt (646-6HEX)

    6" Aluminum Hex Head Pedestal Bolt (646-6HEX)

    Since 1987, all Edson Pedestals use the exclusive Edson Hex Head Aluminum Bolts. With this improvement they lock in place and require only one person to tighten them. They fit flush with the base and the aluminum alloy is the same as the base thus...

    $13.00
  • 6” Aluminum Sheave (ONLY)

    6” Aluminum Sheave (ONLY)

    Edson’s Sheaves may be the answer in many areas of custom boat building, not only for steering but also for centerboards, custom deck hardware, or remote actuators, such as emergency shut off valves and CO2 systems. Great care should be...

    $120.00
  • Flat Conduit Idler with Needle Bearings - 6" Sheave Flat Conduit Idler with Needle Bearings - 6" Sheave

    Flat Conduit Idler with Needle Bearings - 6" Sheave

    Edson’s Flat Conduit Idler allow you to turn steering cable around a sheave rather than through the conduit, reducing wear and friction. Constructed of anodized Aluminum sheaves and a Brass housing, it is designed to be mounted to a...

    $322.00
  • Single Upright Aluminum Sheave Assembly - 8" Sheave

    Single Upright Aluminum Sheave Assembly - 8" Sheave

    Edson’s Single Upright Aluminum Sheave Assembly with a 8" Sheave are specially designed for use in wire rope steering systems for sailboats. The Aluminum Sheaves are ideal for the performance boat that requires sensitive, lightweight steering...

    $558.00
  • Chrome Tiller Head Fitting for 1" Rudder Post

    Chrome Tiller Head Fitting for 1" Rudder Post

    Edson’s Chrome Plated Bronze Tiller Head Fittings have a classic look and feel that compliments both traditional and modern boats alike.  965CH-100 Tiller Head is designed for 1-inch diameter rudder post with a 1/4-inch key. Leaving 1.5-inches...

    $574.00
  • Bronze Rudder Post Stuffing Box - 1.125" ID Bronze Rudder Post Stuffing Box - 1.125" ID Bronze Rudder Post Stuffing Box - 1.125" ID

    Bronze Rudder Post Stuffing Box - 1.125" ID

    Edson's Rudder Post Stuffing Box combines a rudder post bearing with an above-the-waterline stuffing box for. We recommend fiberglassing the stuffing box/bearing to the top of the tubing when the rudder post is in place. This can be done easily using...

    $244.00
  • In-Line Conduit Greaser for 853-250 Conduit In-Line Conduit Greaser for 853-250 Conduit In-Line Conduit Greaser for 853-250 Conduit

    In-Line Conduit Greaser for 853-250 Conduit

    Edson’s In-Line Conduit Greasers are a simple, efficient way to lubricate your conduit. One should be installed in an accessible area of straight conduit as close to the middle of each run as possible - preferably every 3’-5’ where...

    $81.00
  • 17" Conduit Bracket with Rudder Stop 17" Conduit Bracket with Rudder Stop

    17" Conduit Bracket with Rudder Stop

    Pull-Pull Conduit Bracket with Rudderstop is ideal for terminating the conduits at the quadrant when there are no bulkheads to utilize. It is easily bolted through the cockpit sole and comes with its own rudderstop post.  Edson’s #824-17...

    $264.00
  • In-Out Conduit Idler - 6" Sheave In-Out Conduit Idler - 6" Sheave In-Out Conduit Idler - 6" Sheave

    In-Out Conduit Idler - 6" Sheave

    In-Out Conduit Idler is designed to increase the efficiency and sensitivity of a Pull-Pull Conduit System. Engineered with 6” sheaves and three holes to accept Edson’s Conduit End Fittings, the idler makes wire alignment with the sheave...

    $416.00
  • Chain & Wire Kit - 2S15B13 (77105) Chain & Wire Kit - 2S15B13 (77105) Chain & Wire Kit - 2S15B13 (77105) Chain & Wire Kit - 2S15B13 (77105) Chain & Wire Kit - 2S15B13 (77105)

    Chain & Wire Kit - 2S15B13 (77105)

    Edson's Chain & Wire Kits are constructed of the highest quality marine-grade, non-magnetic materials! One length of roller chain and two lengths of wire are assembled with the connections between wire and chain covered in clear shrink...

    $354.00
  • Bronze Hub for 20-inch to 26-inch Dia. Wheels

    Bronze Hub for 20-inch to 26-inch Dia. Wheels

    With Edson's Wheel Bronze Wheel Hub for 20”-26” Diameter Wheels you can make your own traditional mahogany or teak wheels! Using a two piece design, it allows you to assemble your wheel easily.  Bronze Hub 667BR-2 has a outside diameter...

    $809.00
  • 32-inch Classic Teak Yacht Wheel with 1-inch Straight Hub 32-inch Classic Teak Yacht Wheel with 1-inch Straight Hub

    32-inch Classic Teak Yacht Wheel with 1-inch Straight Hub

    Edson's Classic Teak Yacht Wheel is the true original! In production for over 125 years, this is a wheel that belongs on any classic yacht or stately passage-maker. Handcrafted to the highest offshore-quality standards, and will provide years...

    $3,593.00